Avanti Beverage Dispenser BD7000 User Manual

0

Out of 0 Ratings

Owner's of the Avanti Beverage Dispenser BD7000 gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 36
 
8
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of fire, electrical shock, or injury when using
your Beer Dispenser, follow these basic precautions:
Read all instructions before using the unit.
DANGER or WARNING: Risk of child entrapment.
Child entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous . . . even if they will “just sit in the garage a few days”.
Before you throw away your old unit: Take off the door. Leave the shelves in place
so that children may not easily climb inside.
Never allow children to operate, play with, or crawl inside the unit.
Never clean unit parts with flammable fluids. The fumes can create a fire hazard or
explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of
this or any other unit. The fumes can create a fire hazard or explosion.
-Save these instructions-
INSTALLATION INSTRUCTIONS
Before Using Your Beer Dispenser
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
1 Instruction Manual 1 Beer Keg Coupler (Sankey Tap)
1 Safety Guard Rail 10 Keg Coupler Sealing Rings (Plastic Bag)
1 Drip Tray Assembly (Two pieces) 1 Metal Wrench for Faucet installation
1 Beer Keg Support Plate (Plastic) 1 Steel Clamp for Hose (RED) installation
2 Refrigerator Shelves (Wire) 1 Beer Hose (Clear) with Sankey connector
1 Beer Tower Assembly 1 CO2 Tank and Accessories
1 – Faucet
1 – Pull Handle (Black)
1 – Tower Top Cover (Plastic)
1 – Mylar Washer
2 – Faucet Sealing Rings (Plastic Bag)
1 – CO2 Cylinder / Tank (Empty)
1 – CO
2 Cylinder / Tank Cushion
1 – CO
2 Regulator
1 – CO
2 Air Hose (Red) with connector
1 – CO
2 Cylinder / Tank – Holder / Fastener
Before connecting the Beer Dispenser to the power source, let it stand upright for
approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system
from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Installation of Your Beer Dispenser
This appliance is designed to be free standing indoor use only, and should not be recessed or
built-in. If used outdoors, the unit must be protected from exposure to all types of harsh
weather conditions. High temperatures will affect the units cooling efficiency.
Place your Beer Dispenser on a floor that is strong enough to support the Beer Dispenser
when it is fully loaded.
Allow 5 inches of space between the back and sides of the Beer Dispenser,
which allows the proper air circulation to cool the compressor and condenser.
Locate the Beer Dispenser away from direct sunlight and sources of heat (stove, heater,
radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase
electrical consumption. Extreme cold ambient temperatures may also cause the Beer
Dispenser not to perform properly.
Avoid locating the Beer Dispenser in moist areas.
Plug the Beer Dispenser into an exclusive, properly installed-grounded wall outlet. Do not
under any circumstances cut or remove the third (ground) prong from the power cord. Any

   Find Your Products By Category