Viking Microwave Oven DMOC205SS User Manual

3.1

Out of 8 Ratings

Owner's of the Viking Microwave Oven DMOC205SS gave it a score of 3.1 out of 5. Here's how the scores stacked up:

  • Reliability

    2.88 out of 5

  • Durability

    3.0 out of 5

  • Maintenance

    3.25 out of 5

  • Performance

    3.38 out of 5

  • Ease of Use

    2.88 out of 5
of 48
 
30
DMOC205SS
VMOC205SS
POSITIVE LOCK
®
CONNECTOR (NO-CASE TYPE) REMOVAL
Push the lever of positive lock
®
connector. Pull down on the
positive lock
®
connector.
CAUTION: WHEN YOU CONNECTING THE POSITIVE
LOCK
®
CONNECTORS TO THE TERMINALS,
INSTALL THE POSITIVE LOCK
®
SO THAT
THE LEVER FACES YOU.
Figure C-1. Positive lock
®
connector
CONVECTION MOTOR REMOVAL
1.
Disconnect oven from power supply and remove outer case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from the convection motor.
Remove the convection fan belt.
4. Remove two (2) screws holding the convection motor
mounting angle to the heater duct and base cabinet.
5. Take out the convection motor assembly from the unit.
The convection motor assembly is now free.
6. Remove two (2) screws and nuts holding the motor to
mounting angle.
7. Remove pulley (M) from the motor shaft. Convection
motor is now free.
HIGH VOLTAGE RECTIFIER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Remove one (1) screw holding the rectifier assembly to
the capacitor holder.
4. Disconnect the rectifier assembly from the capacitor
1. Disconnect the oven from power supply.
Remove the turntable tray, and the turntable support out
of the oven cavity.
2. Turn the oven upside down and remove one (1) screw
holding the turntable motor cover to the base plate and
take off the turntable motor cover.
TURNTABLE MOTOR REMOVAL
3. Disconnect wire lead from the turntable motor.
4. Remove the two (2) screws holding the turntable motor
and coupling mounting plate to the oven cavity bottom.
5. Turntable motor, Coupling mounting plate and Thermal
protection plate bottom will be free.
DAMPER ASSEMBLY REMOVAL
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect wire leads from damper motor and damper
switch.
4. Remove two (2) oven side screws holding damper motor
angle to thermal protection plate (right).
5. Damper assembly is free.
6. Remove one (1) screw holding damper motor to damper
motor angle and one (1) screw holding damper switch to
damper motor angle.
7. Damper motor and switch are free.
and magnetron.
CAUTION: WHEN REPLACING THE SILICON RECTIFIER
ASSEMBLY, THE GROUND SIDE TERMINAL
MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.
1. Disconnect oven from power supply and remove outer
case.
2. Discharge the high voltage capacitor.
3. Disconnect the high voltage wire leads and rectifier
assembly from high voltage capacitor and magnetron.
4. Disconnect filament lead of transformer from high voltage
capacitor.
HIGH VOLTAGE CAPACITOR REMOVAL
5. Disconnect high voltage wire lead of capacitor from
transformer.
6. Remove one (1) screw and washer holding the rectifier
from the capacitor holder.
7. Remove one (1) screw holding the capacitor holder to
the rear cabinet.
8. Remove the capacitor from the holder.
Terminal
Push
Pull down
1
2
Lever
Positive lock®
connector

   Find Your Products By Category