0
Owner's of the Kenwood GPS Receiver DNX572BH gave it a score of 0 out of 5. Here's how the scores stacked up:
English ñ 17
Call using the preset number
1) Touch [Preset #] to start calling the
corresponding phone number.
2) Touch [
].
Call by voice
You can make a voice call using the voice
recognition function of the cell-phone.
1) Touch [ ].
2) Pronounce the name registered in the cell-
phone.
✎ NOTE
• For detailed operation, see Using Hands-Free Unit
(P.87) in the Instruction Manual.
Installation
ÑBefore Installation
Before installation of this unit, please note the
following precautions.
#WARNINGS
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground), you
may cause a short circuit, that in turn may start a fire.
Always connect those wires to the power source
running through the fuse box.
• Do not cut out the fuse from the ignition wire (red)
and the battery wire (yellow). The power supply
must be connected to the wires via the fuse.
#CAUTION
• Install this unit in the console of your vehicle.
Do not touch the metal part of this unit during and
shortly after the use of the unit. Metal part such as
the heat sink and enclosure become hot.
✎ NOTE
• Mounting and wiring this product requires skills and
experience. For best safety, leave the mounting and
wiring work to professionals.
•
Ma
ke sure to ground the unit to a negative 12V DC
power supply.
•
Do n
ot install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
•
Do n
ot use your own screws. Use only the screws
provided. If you use the wrong screws, you could
damage the unit.
•
If t
he power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched
the chassis of the vehicle and the protection function
may have been activated. Therefore, the speaker wire
should be checked.
•
If y
our car’s ignition does not have an ACC position,
connect the ignition wires to a power source that
can be turned on and off with the ignition key. If you
connect the ignition wire to a power source with a
constant voltage supply, such as with battery wires,
the battery may be drained.
•
If t
he console has a lid, make sure to install the unit so
that the front panel will not hit the lid when closing
and opening.
•
If t
he fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the old
fuse with one with the same rating.
•
In
sulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not
remove the caps on the ends of the unconnected
wires or the terminals.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or
fail to work if you share the ¤ wires or ground them to
any metal part in the car.
•
Wh
en only two speakers are being connected to
the system, connect the connectors either to both
the front output terminals or to both the rear output
terminals (do not mix front and rear). For example,
if you connect the ¢ connector of the left speaker
to a front output terminal, do not connect the ¤
connector to a rear output terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
•
Mo
unt the unit so that the mounting angle is 30° or
less.
•
Th
is unit has the cooling fan to decrease the internal
temperature. Do not mount the unit in a place where
the cooling fan of the unit is blocked. Blocking these
openings will inhibit the cooling of the internal
temperature and result in malfunction.
Cooling fan
• Do not press hard on the panel surface when installing
the unit to the vehicle. Otherwise scars, damage, or
failure may result.
Find Your Products By Category
Please Login
